Daikin AC Error Codes: A Complete Guide to Troubleshooting and Fixes

When your Daikin air conditioner stops working or displays an error code, it can be frustrating and confusing. Daikin, a leading brand in the HVAC industry, uses error codes to help users diagnose and resolve issues with their AC units. Understanding these error codes is crucial for maintaining your AC’s performance and avoiding costly repairs.

In this comprehensive guide, we’ll explore common Daikin AC error codes, their meanings, and step-by-step solutions to fix them. Whether you’re a homeowner or a technician, this article will equip you with the knowledge to troubleshoot Daikin AC issues effectively.


Why Do Daikin ACs Display Error Codes?

Daikin air conditioners are equipped with advanced self-diagnostic systems that monitor the unit’s performance. When the system detects an issue, it displays an error code on the indoor unit’s display panel or remote control. These codes help identify the problem, making it easier to troubleshoot and resolve.


Common Daikin AC Error Codes and Their Meanings

Here’s a list of the most common Daikin AC error codes, along with their causes and solutions:


1. Error Code E0: Indoor Unit PCB Malfunction

  • Meaning: This error indicates a problem with the indoor unit’s printed circuit board (PCB).
  • Causes: Faulty wiring, power surges, or a damaged PCB.
  • Solutions:
    1. Turn off the AC and unplug it from the power source.
    2. Check for loose or damaged wires and reconnect or replace them.
    3. If the issue persists, contact a certified technician to inspect or replace the PCB.

2. Error Code E1: Outdoor Unit PCB Malfunction

  • Meaning: This code points to an issue with the outdoor unit’s PCB.
  • Causes: Electrical faults, overheating, or component failure.
  • Solutions:
    1. Turn off the AC and inspect the outdoor unit for visible damage.
    2. Clean the outdoor unit to ensure proper airflow.
    3. If the problem continues, seek professional help to repair or replace the PCB.

3. Error Code E3: High Pressure Protection

  • Meaning: The AC’s high-pressure sensor has detected excessive pressure in the refrigerant system.
  • Causes: Blocked condenser coils, dirty filters, or overcharged refrigerant.
  • Solutions:
    1. Clean or replace the air filters.
    2. Check the condenser coils for dirt or debris and clean them.
    3. If the refrigerant level is too high, call a technician to adjust it.

4. Error Code E4: Low Pressure Protection

  • Meaning: The low-pressure sensor has detected insufficient pressure in the refrigerant system.
  • Causes: Refrigerant leaks, clogged filters, or a faulty expansion valve.
  • Solutions:
    1. Inspect the refrigerant lines for leaks and repair them.
    2. Clean or replace the air filters.
    3. If the issue persists, consult a professional to check the expansion valve.

5. Error Code E5: Compressor Overload

  • Meaning: The compressor is overheating or drawing too much current.
  • Causes: Dirty coils, low refrigerant levels, or a faulty compressor.
  • Solutions:
    1. Clean the condenser and evaporator coils.
    2. Check the refrigerant level and top it up if necessary.
    3. If the compressor is faulty, it may need to be replaced by a technician.

6. Error Code E6: Communication Error

  • Meaning: There’s a communication issue between the indoor and outdoor units.
  • Causes: Loose or damaged wiring, faulty PCBs, or signal interference.
  • Solutions:
    1. Inspect the wiring between the indoor and outdoor units.
    2. Tighten or replace any loose or damaged wires.
    3. If the problem persists, contact a technician to check the PCBs.

7. Error Code E7: Fan Motor Malfunction

  • Meaning: The indoor or outdoor fan motor is not functioning properly.
  • Causes: Dirty fan blades, motor failure, or electrical issues.
  • Solutions:
    1. Clean the fan blades and ensure they can rotate freely.
    2. Check the motor for signs of damage or wear.
    3. If the motor is faulty, it may need to be replaced.

8. Error Code E8: Temperature Sensor Fault

  • Meaning: The indoor or outdoor temperature sensor is not working correctly.
  • Causes: Sensor damage, loose connections, or wiring issues.
  • Solutions:
    1. Inspect the sensor for damage and replace it if necessary.
    2. Check the wiring and connections to ensure they’re secure.
    3. If the issue continues, consult a technician.

9. Error Code E9: Water Level Alarm

  • Meaning: The drain pan is full, or the drain pump is not working.
  • Causes: Clogged drain pipe, faulty pump, or improper installation.
  • Solutions:
    1. Clean the drain pipe to remove any blockages.
    2. Check the drain pump and replace it if necessary.
    3. Ensure the AC is installed at the correct angle for proper drainage.

10. Error Code EA: Power Supply Issue

  • Meaning: There’s a problem with the AC’s power supply.
  • Causes: Voltage fluctuations, faulty wiring, or a tripped circuit breaker.
  • Solutions:
    1. Check the power supply and ensure it’s stable.
    2. Inspect the wiring for damage and repair it.
    3. Reset the circuit breaker if it has tripped.

How to Reset Daikin AC Error Codes

If you’ve resolved the issue causing the error code, you can reset your Daikin AC using the following steps:

  1. Turn off the AC using the remote control or power button.
  2. Unplug the AC from the power source for 5-10 minutes.
  3. Plug the AC back in and turn it on.
  4. Check if the error code has cleared.

If the error code reappears, the issue may require professional attention.


Preventive Maintenance Tips to Avoid Error Codes

To keep your Daikin AC running smoothly and avoid error codes, follow these maintenance tips:

  1. Clean or Replace Filters Regularly: Dirty filters can cause airflow issues and trigger error codes.
  2. Inspect and Clean Coils: Ensure the condenser and evaporator coils are free of dirt and debris.
  3. Check Refrigerant Levels: Low or high refrigerant levels can lead to system malfunctions.
  4. Schedule Annual Maintenance: Hire a professional to inspect and service your AC annually.
  5. Monitor Power Supply: Ensure the AC is connected to a stable power source.

When to Call a Professional

While many Daikin AC error codes can be resolved with basic troubleshooting, some issues require professional expertise. Contact a certified technician if:

  • The error code persists after troubleshooting.
  • You suspect a refrigerant leak or compressor failure.
  • The wiring or PCB needs repair or replacement.

Conclusion

Understanding Daikin AC error codes is essential for maintaining your air conditioner’s performance and avoiding costly repairs. By following this guide, you can diagnose and resolve common issues quickly and efficiently. Remember, regular maintenance is key to preventing error codes and ensuring your Daikin AC operates at its best.

If you found this article helpful, share it with others who might benefit from it. For more tips and guides on HVAC systems, stay tuned to our blog!

Scroll to Top